Air Systems ASI-2900 Venturi Style Pneumatic Air Blower
- Used to ventilate explosive and hazardous vapors or fumes safely
- No moving parts, lightweight cast aluminum base
- Static grounding lug is standard, operates on compressed air or steam
- Galvanized steel horn (replaceable), operating pressures up to 140psi
- Large models available up to 8000 cfm capacity – consult factory
Compressed air or saturated steam is the energy resource for these air movers (air horns). They operate on the venturi principle whereby you take a tiny volume of high velocity air from a compressed air source by means of the casting and out the nozzle jets. This generates a venturi action that induces huge volumes of lower velocity air moving by way of the venturi and out the air diffuser. A minimum one/two” I.D. hose is recommended from the air provide resource to the side inlet connection on the blower base. If the air mover is employed to supply fresh air to a confined area, the compressor need to be supplied with a Grade-D air filtration package of enough capacity (cfm). A carbon monoxide monitor with alarm should be put in. 1. Install wanted coupling. Do not use less than one/two” diameter fitting. Attach grounding wire amongst the base of the unit and tank. Do not restrict the internal diameter of the blower base as significant loss of output flow will result. two. Tightly safe the air mover in location prior to turning on the air provide. (The additions of prolonged lengths of duct to the air discharge finish of the blower horn will result in flow reduction.) 3. Attach compressed air resource. 44.00″ All round length, 11.16″ base diameter, 13.00″ horn diameter, 1″ NPT, 10.28″ bolt circle, .43″ base slot, 22.1 lbs weight. Revision one, testing and specifications completed: June 9, 2005. Testing conditions: 81 F, 73 percent R.H., barometric stress of 30.19 inches. Delivery air produced by an atlas copco 375cfm compressor. Air pressure regulated by a wilkerson regulator with pre-filter and gauge. Inline 400 cfm flow meter installed on delivery air line. Air flow measurements taken at a regular 12-point air outlet cone configuration. Air flow measuring gadget is a Extech Instruments Model 451126 vane design thermo- anemometer.
Air Systems ASI-1000 Venturi Style Pneumatic Air Blower
- Used to ventilate explosive and hazardous vapors or fumes safely
- No moving parts, lightweight cast aluminum base
- Static grounding lug is standard, operates on compressed air or steam
- Galvanized steel horn (replaceable), operating pressures up to 140psi
- Large models available up to 8000 cfm capacity – consult factory
Compressed air or saturated steam is the power resource for these air movers (air horns). They operate on the venturi principle whereby you take a little volume of higher velocity air from a compressed air supply by means of the casting and out the nozzle jets. This generates a venturi action that induces significant volumes of low velocity air moving by means of the venturi and out the air diffuser. A minimum 1/two” I.D. hose is advised from the air supply source to the side inlet connection on the blower base. The compressed air volume requirement can be determined by checking the chart on air consumed at numerous inlet pressures positioned on page three. If the air mover is utilised to supply fresh air to a confined space, the compressor need to be supplied with a Grade-D air filtration package of enough capability (cfm). A carbon monoxide keep track of with alarm should be installed. one. Set up desired coupling. Do not use significantly less than 1/2″ diameter fitting. Attach grounding wire amongst the base of the unit and tank. Do not restrict the internal diameter of the blower base as extreme reduction of output flow will result. 2. Tightly secure the air mover in location prior to turning on the air provide. (The additions of prolonged lengths of duct to the air discharge end of the blower horn will cause flow loss.) 3. Attach compressed air supply. 16.31″ General length, 7.38″ base diameter, six.19″ horn diameter, one/two” NPT, six.75″ bolt circle, .31″ base slot, five.three lbs weight. Revision one, testing and specifications finished: June 9, 2005. Testing ailments: 81 F, 73 percent R.H., barometric stress of 30.19 inches. Delivery air created by an atlas copco 375cfm compressor. Air stress regulated by a wilkerson regulator with pre-filter and gauge. Inline 400 cfm flow meter installed on delivery air line. Air flow measurements taken at a standard twelve-point air outlet cone configuration. Air flow measuring gadget is a Extech Instruments Model 451126 vane style thermo- anemometer.
Related posts:
